1.Exhaust System are used for extracting dust and vapors during laser processing. 2.Software are used for marking layout,barcode marking and laser control. 3.Multi Color Jet used for automatic manufacture of multi-color rubber stamps. 4.Laser Fume Filter removes the need to extract through the wall. 5.Laser Safety Glasses provide excellent filters to protect the eyes against laser beam. 6.High Precision Laser Cooling System is used for medium power laser tube. 7.Speedy 100 is used for CO2 laser and flatbed laser type. 8.ProMarker 100 is used for Galvo Fiber laser type. 9.CO2 Laser Beam Expanders are used to keep the beam collimated. 10.Laser Focus Lens are used to focus laser beam during cutting process.
prepared by TENGKU MUHAMMAD BIN TENGKU ABDUL GHANI
1 - Toggle - Toggle are used to On or Off machine. 2 - Clamp - Clamp are used to hold material. 3 - Runner - Runner is used to easily move the product. 4 - Ejector pin - Ejector pin are used to pull out item from moulding. 5 - Operator - Operator on duty today is Salmah. 6 - Flow mark - Flow mark happen because material move to slow. 7 - Barrel - Barrel are used to put chaff. 8 - Overflow - Overflow happen when temperature is high. 9 - Packing - Packing is Shah job. 10- Pressure - Pressure are used in stamping machine.
1.injection injection is a manufacturing process 2.cycle time cycle time is an estimate time for finishing goods 3.elasticity elasticity is an important element for plastic product 4.pellets pellets is a material using for injection 5.scrap scrap is a excess material that are removal from molded 6.thermoplastic thermoplastic is a substances that can be soften and harden in some process 7.thermoset thermoset is a substances that doesn't melt during heating process 8.toggle toggle is a type of clamping unit 9.assembly assembly is a process that joint two part under one process 10.draft draft is a slight taper that using for removal of excess material
1)CURRENT current is very dangerous when toched 2)TESTPEN testpen is for check flow of current 3)FUSE fuse is for limit the current 4)CIRCUIT BREAKER circuit breaker is to distribute current 5)PULG plug is connection between power and equipment 6)BATTERY battery is one of power supply 7)POWER STRIP power strip is distribution current 8)WIRE wire is for joint between computer to plug 9)CIRCUIT BOARD circuit board used for conneting circuit 10)SERIES CIRCUIT series circuit is a circuit connected in series
1)Stamping : Stamping is a process that use for produce a part from a metal sheet. 2)Die : Die is an important thing in stamping process. 3)Sensor : Sensor is a safety precaution electronic part that assembled in press machine. 4)Milling : Milling is one of the finishing process in producing dies. 5)Casting : Casting is a manufacturing process which is a molten metal is injected or poured into a mold. 6)Punch : Punch is a important part in dies. 7)Bush : Bush is a safety part in die that avoid the upper die lip away from lower die. 8)Fitting : Fitting is a trial process to check whether the die is ready to use or not. 9)Dent : Dent is a scratch or scar in stamped part after stamping process. 10)Stroke : Stroke happens after upper die member is closed upon the lower die member in stamping process.
1. assembly -car spare part assembly take place in NHF factory
2. additive -additive is a substance compound which to enhance or improve certain characteristic
3. alloy -manufacture will use alloy as one of the element to create plastic
4. aspect ratio -the ability to adjust everything from brightness, sound and aspect ratio, coupled with plenty of scope to input components
5. cooling time -those mixture will have cooling time after extreme heat
6. element -plastic are composed of various elements such as carbon, hydrogen, oxygen, nitrogen and many more
7. compound -the start of making plastic is to subject naphtha to a cracking process in which complex organic compounds are separated into smaller molecules
8. blowing agents -many plastic products are cellular in structure. these expanded or formed products can be made from base polymers by the addition of what are known as 'blowing agents'
9. colorants - plastic will go through colorants process where plastic can be colored by using either dyes or pigments.
10. extrusion -Thermoplastic granules are forced through a heated barrel and the fused polymer is then squeezed through a die that is the profile of the extruded component. this process call as extrusion
1. Assembly - assambly is a process that joint tow part into one part 2. Crack - crack is a tearing in part of product 3. Draft - draft is a removal of the object from the mold 4. Alloy - alloy is used to denote blends of polymers 5. Bubbles - bubbles is formed material in a air or gas pockets 6. Durometer - durometer is used to get the fitting measuring of a material 7. Gate - gate is a channel where the molten resin flows into the cavity 8. Jig - jig is a holding tool that using during the assambly 9. Plots - plots is analysis results from graphical representations 10. Ram - ram is a forward motion that forces the mold cavity
1)Repair = Maintenance work is to repair a broken equipment 2)Schedule maintenance = Any machine should have the schedule maintenance 3)maintenance = Kamal is working at department maintenance 4)tool = Must use compatible tool 5)safety = Safety is first 6)inspection = Always do an inspection of the machine 7)responsibility = Every worker should have responsibility 8)work request = Work request is important before repairing something 9)downtime = Each machine must enter the downtime when the machine is damage 10)Maintenance Strategy = Before do the job must have maintenance strategy
1.TruDisk Laser are ideal for welding ang cutting matel where high quality,continious high power and very good beam power. 2.Cleaning set clearly arrangedperfectily matheh and always at hard. 3.Dynamic beam waist adapting or variation of the effactive focal length,versatile expansion of the operative range of moderm laser welding and cutting sydtems. 4.laser chiller unit suitable for water cooled CO2 laser tube. 5.CO2 laser safty glasses ideal for education and industry. 6.Laser fokus lens is used to fokus laser beam,the wavelength is 10.6um.
14 comments:
1) Solidwork
Solidwork is one of the software in design.
2) Fillet
Fillet is applied at the edges of mould design.
3) Runner
Runner is one of the important parts in designing the mould.
4) Sprue
Sprue is needed to avoid turbulence before entering the runner.
5) Vent
Vent is used to avoid the molds in mould shrink.
6) Construction drawing
Construction drawing is important in design.
7) Designer
Designer is doing his job.
8) Feedback
Feedback is needed to improve the design.
9) Millimeter
Millimeter is the common units used in design.
10) Cycle time
Cycle time is the total time taken to complete one cycle.
Farah Nabilah binti Mansor
1.Test Pen
- Test pen is used to detect current.
2.Cutter
- I need a cutter to cut a cable.
3.Cable
-We need to use long cable to finish this wiring.
4.Safety Boots
-Safety Boots are used for insulation from electrical shock.
5.Screw Driver
-Screw Driver is the tool use to loose screw.
6.Multimeter
-Multimeter is important to measure the voltage.
7.Tool Box
-I want a tool box to keep my equipment.
8.Sensor
-Sensor used to detect object like a metal,plastic.
9.Ear Plug
-Ear Plug is used to protect ear in a noisy place.
10.Spectacles
-I use a spectales during welding.
Prepared By : Muhammad Amirul Affendi Bin Asnan
1.Exhaust System are used for extracting dust and vapors during laser processing.
2.Software are used for marking layout,barcode marking and laser control.
3.Multi Color Jet used for automatic manufacture of multi-color rubber stamps.
4.Laser Fume Filter removes the need to extract through the wall.
5.Laser Safety Glasses provide excellent filters to protect the eyes against laser beam.
6.High Precision Laser Cooling System is used for medium power laser tube.
7.Speedy 100 is used for CO2 laser and flatbed laser type.
8.ProMarker 100 is used for Galvo Fiber laser type.
9.CO2 Laser Beam Expanders are used to keep the beam collimated.
10.Laser Focus Lens are used to focus laser beam during cutting process.
prepared by TENGKU MUHAMMAD BIN TENGKU ABDUL GHANI
1)POWER SUPPLY
-Power supply is used to start the machine
2)MINI CUTTER
-Azrin using the mini cutter for cutting wire
3)TIMING LIGHT CORD
-Timing light cord using to check at the leakage current
4)CHAIN RIVET EXTRACTOR
-Firman want to cut the chains and asked Bob to take chain rivet extractor
5)CABLE CUTTER
-Cable cutter is used for cut cable wire
6)SAFETY
-Every employee will be reminded of safety in the work place.
7)EARMUFFS
-Earmuffs be used in the workplace are noisy.
Prepared by:MOHAMAD SYAWAN BIN SAAD RONI
1 - Toggle
- Toggle are used to On or Off machine.
2 - Clamp
- Clamp are used to hold material.
3 - Runner
- Runner is used to easily move the product.
4 - Ejector pin
- Ejector pin are used to pull out item from moulding.
5 - Operator
- Operator on duty today is Salmah.
6 - Flow mark
- Flow mark happen because material move to slow.
7 - Barrel
- Barrel are used to put chaff.
8 - Overflow
- Overflow happen when temperature is high.
9 - Packing
- Packing is Shah job.
10- Pressure
- Pressure are used in stamping machine.
NUR MOHD FIRMAN BIN MOHD HAMIL
1) Condition
- The injection machine is in good condition
2) Controller
- Abu use the controller to works the machine
3) Ground
- The wire from the ground is very dangerous
4) Fitting
- Fitting is very important in quality control
5)Component
- The electric component must always clean
6) Assembly
- Hassan works in assembly area
7) Accident
- To avoid accident, we must be careful
8) Factory
- The mechatronics factory state in klang.
9) Lathe machine
- Kassim a very expert in lathe machine
10) Test Pen
- Jason always keep his test pen in his pocket
-Amiin Firdaus Bin Mohd Rasol-
1.injection
injection is a manufacturing process
2.cycle time
cycle time is an estimate time for finishing goods
3.elasticity
elasticity is an important element for plastic product
4.pellets
pellets is a material using for injection
5.scrap
scrap is a excess material that are removal from molded
6.thermoplastic
thermoplastic is a substances that can be soften and harden in some process
7.thermoset
thermoset is a substances that doesn't melt during heating process
8.toggle
toggle is a type of clamping unit
9.assembly
assembly is a process that joint two part under one process
10.draft
draft is a slight taper that using for removal of excess material
prepared by maki nun amin
1)CURRENT
current is very dangerous when toched
2)TESTPEN
testpen is for check flow of current
3)FUSE
fuse is for limit the current
4)CIRCUIT BREAKER
circuit breaker is to distribute current
5)PULG
plug is connection between power and equipment
6)BATTERY
battery is one of power supply
7)POWER STRIP
power strip is distribution current
8)WIRE
wire is for joint between computer to plug
9)CIRCUIT BOARD
circuit board used for conneting circuit
10)SERIES CIRCUIT
series circuit is a circuit connected in series
sofwan and shafiq
1)Stamping : Stamping is a process that use for produce a part from a metal sheet.
2)Die : Die is an important thing in stamping process.
3)Sensor : Sensor is a safety precaution electronic part that assembled in press
machine.
4)Milling : Milling is one of the finishing process in producing dies.
5)Casting : Casting is a manufacturing process which is a molten metal is injected
or poured into a mold.
6)Punch : Punch is a important part in dies.
7)Bush : Bush is a safety part in die that avoid the upper die lip away from
lower die.
8)Fitting : Fitting is a trial process to check whether the die is ready to use or
not.
9)Dent : Dent is a scratch or scar in stamped part after stamping process.
10)Stroke : Stroke happens after upper die member is closed upon the lower die
member in stamping process.
Prepared by :Hairullah Bin Mohd Tauhid
1. assembly
-car spare part assembly take place in NHF factory
2. additive
-additive is a substance compound which to enhance or improve certain characteristic
3. alloy
-manufacture will use alloy as one of the element to create plastic
4. aspect ratio
-the ability to adjust everything from brightness, sound and aspect ratio, coupled with plenty of scope to input components
5. cooling time
-those mixture will have cooling time after extreme heat
6. element
-plastic are composed of various elements such as carbon, hydrogen, oxygen, nitrogen and many more
7. compound
-the start of making plastic is to subject naphtha to a cracking process in which complex organic compounds are separated into smaller molecules
8. blowing agents
-many plastic products are cellular in structure. these expanded or formed products can be made from base polymers by the addition of what are known as 'blowing agents'
9. colorants
- plastic will go through colorants process where plastic can be colored by using either dyes or pigments.
10. extrusion
-Thermoplastic granules are forced through a heated barrel and the fused
polymer is then squeezed through a die that is the profile of the extruded
component. this process call as extrusion
prepared by MUHAMMAD FADHLI AMRIN BIN AMRIN
1. Assembly - assambly is a process that joint tow part into one part
2. Crack - crack is a tearing in part of product
3. Draft - draft is a removal of the object from the mold
4. Alloy - alloy is used to denote blends of polymers
5. Bubbles - bubbles is formed material in a air or gas pockets
6. Durometer - durometer is used to get the fitting measuring of a material
7. Gate - gate is a channel where the molten resin flows into the cavity
8. Jig - jig is a holding tool that using during the assambly
9. Plots - plots is analysis results from graphical representations
10. Ram - ram is a forward motion that forces the mold cavity
+ MOHAMAD AZRIN BIN ABDULLAH +
1)Repair = Maintenance work is to repair a broken equipment
2)Schedule maintenance = Any machine should have the schedule maintenance
3)maintenance = Kamal is working at department maintenance
4)tool = Must use compatible tool
5)safety = Safety is first
6)inspection = Always do an inspection of the machine
7)responsibility = Every worker should have responsibility
8)work request = Work request is important before repairing something
9)downtime = Each machine must enter the downtime when the machine is damage
10)Maintenance Strategy = Before do the job must have maintenance strategy
Prepare by:MUHAMMAD NAIM BIN BAHARUDDIN
1.TruDisk Laser are ideal for welding ang cutting matel where high quality,continious high power and very good beam power.
2.Cleaning set clearly arrangedperfectily matheh and always at hard.
3.Dynamic beam waist adapting or variation of the effactive focal length,versatile expansion of the operative range of moderm laser welding and cutting sydtems.
4.laser chiller unit suitable for water cooled CO2 laser tube.
5.CO2 laser safty glasses ideal for education and industry.
6.Laser fokus lens is used to fokus laser beam,the wavelength is 10.6um.
Prepare by khairul Anuar
1)POWER SUPPLY
-Power supply is used to start the machine
2)MINI CUTTER
-Azrin using the mini cutter for cutting wire
3)TIMING LIGHT CORD
-Timing light cord using to check at the leakage current
4)CHAIN RIVET EXTRACTOR
-Firman want to cut the chains and asked Bob to take chain rivet extractor
5)CABLE CUTTER
-Cable cutter is used for cut cable wire
6)SAFETY
-Every employee will be reminded of safety in the work place.
7)EARMUFFS
-Earmuffs be used in the workplace are noisy.
8)SPECTACLES
-Spectacles is used to cover my eye.
9)WIRE INJECTOR TWIN TYPE
-wire injector twin type is used to combaind the wire.
10)GLOVE
-Use the glove to protect my hand.
prepared by:MOHAMAD SYAZWAN BIN SAAD RONI
Post a Comment