1) The wrench is used to tightened the bolt 2) The hammer is very heavy 3) The cutter is use to cut wire 4) Air gun use compressed air 5) Multi meter is use to measure voltage,current and resistance
Prepared By: 1) Mohammad Shahrezal Bin Othman 2) Mohd Shafiq Khairil Bin Mohd Zain
1- That tool box should be in store room . 2- The multimeter is very important to measure voltage of electricity . 3- The CNC machine is made in Germany . 4- The fuse of each cables must be change at least a year to avoid destruction . 5- Vernier Caliper is the right tool to measure instrument compared to ruler .
1. Digital Multi-metre (DMM) is an electronic measuring instrument that combines several measuring functions in one unit. 2. Safety shoes is used to protect the foot from falling object or compression. 3. Test pen is used to detect voltage presence in a circuit. 4. Spanner is a tool used to turn nuts. 5. A breadboard is a device used as a construction base in developing an electronic circuit.
1. The safety boots were distributed for the new comer in the company. 2. The USB cable was connected to the computer and phone for transferring data. 3. Two batteries are needed to be use for that brand new clock. 4. Microphone is a electronic device to transfer sound wave to electrical signal. 5. The crane is suitable for lifting heavy material in the construction site.
I sketch and draw plans I plan the schedule I check my tools I tighten up my gear I like to move around I cannot discuss things other than work I monitor and inspect across the factory floor I supervise in and out the door I delegate the works I communicate with others I heard complaints I reconciles with them I decide what's best but I'm still careful I don't trip! I assembled my team I wrap things up
Prepared by: Luqmanul Hakeem bin Mohamed Habibollah Muhammad Irfan bin Anuar
7 comments:
1. The grinder is used to remove the burr from the work piece.
2. Use the wire stripper to cut the wire.
3. Mallet is a kind of hammer.
4. Use suitable drill bit size to make the hole.
5. PPE is used to protect the user from hazard conditions.
6. Cable lug is used to ease the electrical maintenance work.
7. All electrical wiring must be installed in the panel enclosure.
Prepared by:
Luqmanul Hakeem bin Mohamed Habibollah
Muhammad Irfan bin Anuar
1) The wrench is used to tightened the bolt
2) The hammer is very heavy
3) The cutter is use to cut wire
4) Air gun use compressed air
5) Multi meter is use to measure voltage,current and resistance
Prepared By:
1) Mohammad Shahrezal Bin Othman
2) Mohd Shafiq Khairil Bin Mohd Zain
1- That tool box should be in store room .
2- The multimeter is very important to measure voltage of electricity .
3- The CNC machine is made in Germany .
4- The fuse of each cables must be change at least a year to avoid destruction .
5- Vernier Caliper is the right tool to measure instrument compared to ruler .
Prepared by Suhaimi and Muhammad Hazwan ;D
1. Digital Multi-metre (DMM) is an electronic measuring instrument that combines several measuring functions in one unit.
2. Safety shoes is used to protect the foot from falling object or compression.
3. Test pen is used to detect voltage presence in a circuit.
4. Spanner is a tool used to turn nuts.
5. A breadboard is a device used as a construction base in developing an electronic circuit.
Prepared by Saiful Islam and Noor Zaidi
1-We must be really careful while working with wire harness machine.
2-Mazda engine schematic is really hard to understand.
3-The company manufactures various kinds of wire harness.
4-That operator uses air driver to tighten the screw.
5-Syahid uses multimeter to check voltage of compressor.
PREPARED BY:
AHMAD RABBANI BIN MOHD AMIN
MUHAMMAD AIMAN SYAHIR BIN MAHMUD
1. The safety boots were distributed for the new comer in the company.
2. The USB cable was connected to the computer and phone for transferring data.
3. Two batteries are needed to be use for that brand new clock.
4. Microphone is a electronic device to transfer sound wave to electrical signal.
5. The crane is suitable for lifting heavy material in the construction site.
Prepared by : SYUKOR, SYAZWAN, HUSAINII
Title : Supervisor Day
I sketch and draw plans
I plan the schedule
I check my tools
I tighten up my gear
I like to move around
I cannot discuss things
other than work
I monitor and inspect
across the factory floor
I supervise in and
out the door
I delegate the works
I communicate with others
I heard complaints
I reconciles with them
I decide what's best
but I'm still careful
I don't trip!
I assembled my team
I wrap things up
Prepared by:
Luqmanul Hakeem bin Mohamed Habibollah
Muhammad Irfan bin Anuar
Post a Comment